ACIDS, BASES AND SALTS

Acid-Base Reactions
Effect of Solvent on Acids
Effect of Solvent on Bases

By the end of the lesson, the learner should be able to:
- Write equations for acid-base reactions
-Explain neutralization process
-Identify products of acid-base reactions
-Demonstrate formation of salt and water
- Explain effect of polar and non-polar solvents on hydrogen chloride
-Investigate HCl behavior in water vs methylbenzene
-Define polar and non-polar solvents
-Explain why acids show properties only in polar solvents

Q/A: Review acid and base definitions. Demonstrate neutralization reactions: HCl + NaOH, H₂SO₄ + Ca(OH)₂, HNO₃ + KOH. Write molecular and ionic equations. Explain H⁺ + OH⁻ → H₂O. Discuss salt formation. Use indicators to show neutralization point.
Teacher demonstration: Dissolve HCl gas in water and methylbenzene separately. Test both solutions with litmus paper, magnesium, and calcium carbonate. Compare observations. Explain polarity of water vs methylbenzene. Discuss dissociation vs molecular solution.

Various acids and bases from previous lessons, indicators, beakers, measuring cylinders, stirring rods
HCl gas, distilled water, methylbenzene, magnesium ribbon, calcium carbonate, litmus paper, test tubes, gas absorption apparatus
Dry ammonia gas, distilled water, methylbenzene, red litmus paper, test tubes, gas collection apparatus

KLB Secondary Chemistry Form 4, Pages 6-7
KLB Secondary Chemistry Form 4, Pages 7-9

ACIDS, BASES AND SALTS

Amphoteric Oxides and Hydroxides
Definition of Salts and Precipitation

By the end of the lesson, the learner should be able to:
- Define amphoteric oxides
-Identify some amphoteric oxides
-Investigate reactions with both acids and alkalis
-Write equations for amphoteric behavior

Class experiment: React Al₂O₃, ZnO, PbO, Zn(OH)₂, Al(OH)₃, Pb(OH)₂ with 2M HNO₃ and 2M NaOH. Warm mixtures. Record observations in table. Write equations showing basic and acidic behavior. Discuss dual nature of amphoteric substances.

Al₂O₃, ZnO, PbO, Zn(OH)₂, Al(OH)₃, Pb(OH)₂, 2M HNO₃, 2M NaOH, boiling tubes, heating source
Na₂CO₃ solution, salt solutions containing various metal ions, test tubes, droppers

KLB Secondary Chemistry Form 4, Pages 10-11

ACIDS, BASES AND SALTS

Solubility of Chlorides, Sulphates and Sulphites

By the end of the lesson, the learner should be able to:
- Find out cations that form insoluble chlorides, sulphates and sulphites
-Write ionic equations for formation of insoluble salts
-Distinguish between sulphate and sulphite precipitates
-Investigate effect of warming on precipitates

Class experiment: Add NaCl, Na₂SO₄, Na₂SO₃ to solutions of Pb²⁺, Ba²⁺, Mg²⁺, Ca²⁺, Zn²⁺, Cu²⁺, Fe²⁺, Fe³⁺, Al³⁺. Warm mixtures. Record observations in table. Test sulphite precipitates with dilute HCl. List soluble and insoluble salts.

2M NaCl, 2M Na₂SO₄, 2M Na₂SO₃, 0.1M salt solutions, dilute HCl, test tubes, heating source

KLB Secondary Chemistry Form 4, Pages 14-16

ACIDS, BASES AND SALTS

Complex Ions Formation

By the end of the lesson, the learner should be able to:
- Explain formation of complex ions
-Investigate reactions with excess sodium hydroxide and ammonia
-Identify metal ions that form complex ions
-Write equations for complex ion formation

Class experiment: Add NaOH dropwise then in excess to Mg²⁺, Ca²⁺, Zn²⁺, Al³⁺, Cu²⁺, Fe²⁺, Fe³⁺, Pb²⁺ solutions. Repeat with NH₃ solution. Record observations showing precipitate formation and dissolution. Write equations for complex ion formation: [Zn(OH)₄]²⁻, [Al(OH)₄]⁻, [Pb(OH)₄]²⁻, [Zn(NH₃)₄]²⁺, [Cu(NH₃)₄]²⁺.

2M NaOH, 2M NH₃ solution, 0.5M salt solutions, test tubes, droppers

KLB Secondary Chemistry Form 4, Pages 15-16

ACIDS, BASES AND SALTS

Solubility and Saturated Solutions

By the end of the lesson, the learner should be able to:
- Define the term solubility
-Determine solubility of a given salt at room temperature
-Calculate mass of solute and solvent
-Express solubility in different units

Class experiment: Weigh evaporating dish and watch glass. Measure 20cm³ saturated KNO₃ solution. Record temperature. Evaporate to dryness carefully. Calculate masses of solute, solvent, and solution. Determine solubility per 100g water and in moles per litre. Discuss definition and significance.

Saturated KNO₃ solution, evaporating dish, watch glass, measuring cylinder, thermometer, balance, heating source

KLB Secondary Chemistry Form 4, Pages 16-18

ACIDS, BASES AND SALTS

Effect of Temperature on Solubility

By the end of the lesson, the learner should be able to:
- Investigate the effect of temperature on solubility of potassium chlorate
-Record temperature at which crystals appear
-Calculate solubility at different temperatures
-Plot solubility curve

Class experiment: Dissolve 4g KClO₃ in 15cm³ water by warming. Cool while stirring and note crystallization temperature. Add 5cm³ water portions and repeat until total volume is 40cm³. Calculate solubility in g/100g water for each temperature. Plot solubility vs temperature graph.

KClO₃, measuring cylinders, thermometer, burette, boiling tubes, heating source, graph paper

KLB Secondary Chemistry Form 4, Pages 18-20

ACIDS, BASES AND SALTS

Solubility Curves and Applications

By the end of the lesson, the learner should be able to:
- Plot solubility curves for various salts
-Use solubility curves to determine mass of crystals formed
-Apply solubility curves to practical problems
-Compare solubility patterns of different salts

Using data from textbook, plot solubility curves for KNO₃, KClO₃, NaCl, CaSO₄. Calculate mass of crystals deposited when saturated solutions are cooled. Work through examples: KClO₃ cooled from 70°C to 30°C. Discuss applications in salt extraction and purification.

Graph paper, ruler, pencil, calculator, data tables from textbook

KLB Secondary Chemistry Form 4, Pages 20-21

ACIDS, BASES AND SALTS

Fractional Crystallization

By the end of the lesson, the learner should be able to:
- Define fractional crystallization
-Apply knowledge of solubility curves in separation of salts
-Calculate masses of salts that crystallize
-Explain separation of salt mixtures

Work through separation problems using solubility data for KNO₃ and KClO₃ mixtures. Calculate which salt crystallizes first when cooled from 50°C to 20°C. Plot combined solubility curves. Discuss applications in Lake Magadi and Ngomeni salt works. Solve practice problems.

Calculator, graph paper, data tables, worked examples from textbook

KLB Secondary Chemistry Form 4, Pages 21-22

ACIDS, BASES AND SALTS

Hardness of Water - Investigation
Types and Causes of Water Hardness

By the end of the lesson, the learner should be able to:
- Determine the effects of various salt solutions on soap
-Identify cations that cause hardness
-Distinguish between hard and soft water
-Investigate effect of boiling on water hardness
- Define temporary and permanent hardness
-Explain causes of temporary hardness
-Explain causes of permanent hardness
-Write equations for decomposition of hydrogen carbonates

Class experiment: Test soap lathering with distilled water, tap water, rainwater, and solutions of MgCl₂, NaCl, Ca(NO₃)₂, CaHCO₃, NaHCO₃, ZnSO₄. Record volumes of soap needed. Boil some solutions and retest. Compare results and identify hardness-causing ions.
Q/A: Review previous experiment results. Explain temporary hardness caused by Ca(HCO₃)₂ and Mg(HCO₃)₂. Write decomposition equations when boiled. Explain permanent hardness caused by CaSO₄, MgSO₄, Ca(NO₃)₂, Mg(NO₃)₂. Discuss why permanent hardness cannot be removed by boiling.

Soap solution, burette, various salt solutions, conical flasks, distilled water, tap water, rainwater, heating source
Student books, examples from previous experiment, chalkboard for equations

KLB Secondary Chemistry Form 4, Pages 22-24
KLB Secondary Chemistry Form 4, Pages 24-25

ACIDS, BASES AND SALTS

Effects of Hard Water

By the end of the lesson, the learner should be able to:
- State disadvantages of hard water
-State advantages of hard water
-Explain formation of scum and fur
-Discuss economic and health implications

Discussion based on practical experience: Soap wastage, scum formation on clothes, fur in kettles and pipes, pipe bursting in boilers. Advantages: calcium for bones, protection of lead pipes, use in brewing. Show examples of fur deposits. Calculate economic costs of hard water in households.

Samples of fur deposits, pictures of scaled pipes, calculator for cost analysis

KLB Secondary Chemistry Form 4, Pages 24-25

ACIDS, BASES AND SALTS

Methods of Removing Hardness I

By the end of the lesson, the learner should be able to:
- Explain removal of hardness by boiling
-Explain removal by distillation
-Write equations for these processes
-Compare effectiveness of different methods

Demonstrate boiling method: Boil hard water samples from previous experiments and test with soap. Write equations for Ca(HCO₃)₂ and Mg(HCO₃)₂ decomposition. Discuss distillation method using apparatus setup. Compare costs and effectiveness. Explain why boiling only removes temporary hardness.

Hard water samples, heating source, soap solution, distillation apparatus diagram

KLB Secondary Chemistry Form 4, Pages 25-26

ACIDS, BASES AND SALTS

Methods of Removing Hardness II

By the end of the lesson, the learner should be able to:
- Explain removal using sodium carbonate
-Describe ion exchange method
-Explain removal using calcium hydroxide and ammonia
-Write equations for all processes

Demonstrate addition of Na₂CO₃ to hard water - observe precipitation. Explain ion exchange using resin (NaX) showing Ca²⁺ + 2NaX → CaX₂ + 2Na⁺. Discuss regeneration with brine. Write equations for Ca(OH)₂ and NH₃ methods. Compare all methods for effectiveness and cost.

Na₂CO₃ solution, hard water samples, ion exchange resin diagram, Ca(OH)₂, NH₃ solution

KLB Secondary Chemistry Form 4, Pages 25-26

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Endothermic and Exothermic Reactions

By the end of the lesson, the learner should be able to:
- Define endothermic and exothermic reactions using ΔH notation
-Investigate temperature changes when ammonium nitrate and sodium hydroxide dissolve in water
-Explain observations made during dissolution
-Draw energy level diagrams for endothermic and exothermic reactions

Class experiment: Wrap 250ml plastic beakers with tissue paper. Dissolve 2 spatulafuls of NH₄NO₃ in 100ml distilled water, record temperature changes. Repeat with NaOH pellets. Compare initial and final temperatures. Draw energy level diagrams showing relative energies of reactants and products.

250ml plastic beakers, tissue paper, rubber bands, NH₄NO₃, NaOH pellets, distilled water, thermometers, spatulas, measuring cylinders

KLB Secondary Chemistry Form 4, Pages 29-31

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy Notation and Energy Content

By the end of the lesson, the learner should be able to:
- Define enthalpy and enthalpy change
-Use the symbol ΔH to represent enthalpy changes
-Calculate enthalpy changes using the formula ΔH = H(products) - H(reactants)
-Distinguish between positive and negative enthalpy changes

Q/A: Review previous experiment results. Introduce enthalpy symbol H and enthalpy change ΔH. Calculate enthalpy changes from previous experiments. Explain why endothermic reactions have positive ΔH and exothermic reactions have negative ΔH. Practice calculations with worked examples.

Student books, calculators, worked examples from textbook, chalkboard for calculations

KLB Secondary Chemistry Form 4, Pages 31-32

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Bond Breaking and Bond Formation

By the end of the lesson, the learner should be able to:
- Explain that energy changes are due to bond breaking and bond formation
-Describe bond breaking as endothermic and bond formation as exothermic
-Investigate energy changes during melting and boiling
-Plot heating curves for pure substances

Class experiment: Heat crushed ice while stirring with thermometer. Record temperature every minute until ice melts completely, then continue until water boils. Plot temperature-time graph. Explain constant temperature during melting and boiling in terms of bond breaking. Discuss latent heat of fusion and vaporization.

Crushed pure ice, 250ml glass beakers, thermometers, heating source, stopwatch, graph paper, stirring rods

KLB Secondary Chemistry Form 4, Pages 32-35

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Latent Heat of Fusion and Vaporization

By the end of the lesson, the learner should be able to:
- Define latent heat of fusion and molar heat of fusion
-Define latent heat of vaporization and molar heat of vaporization
-Explain why temperature remains constant during phase changes
-Relate intermolecular forces to melting and boiling points

Discussion based on previous heating curve experiment. Explain energy used to overcome intermolecular forces during melting and boiling. Compare molar heats of fusion and vaporization for water and ethanol. Relate strength of intermolecular forces to magnitude of latent heats. Calculate energy required for phase changes.

Data tables showing molar heats of fusion/vaporization, calculators, heating curves from previous lesson

KLB Secondary Chemistry Form 4, Pages 32-35

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Bond Energy Calculations
Determination of Enthalpy of Solution I

By the end of the lesson, the learner should be able to:
- Calculate energy changes in reactions using bond energies
-Apply the formula: Heat of reaction = Bond breaking energy + Bond formation energy
-Determine whether reactions are exothermic or endothermic
-Use bond energy data to solve problems
- Determine the enthalpy changes of solution of ammonium nitrate and sodium hydroxide
-Calculate enthalpy change using ΔH = mcΔT
-Calculate number of moles of solute dissolved
-Determine molar heat of solution

Work through formation of HCl from H₂ and Cl₂ using bond energies. Calculate energy required to break H-H and Cl-Cl bonds. Calculate energy released when H-Cl bonds form. Apply formula: ΔH = Energy absorbed - Energy released. Practice with additional examples. Discuss why calculated values may differ from experimental values.
Class experiment: Dissolve exactly 2.0g NH₄NO₃ in 100ml distilled water in plastic beaker. Record temperature change. Repeat with 2.0g NaOH. Calculate enthalpy changes using ΔH = mcΔT where m = 100g, c = 4.2 kJ kg⁻¹K⁻¹. Calculate moles dissolved and molar heat of solution.

Bond energy data tables, calculators, worked examples, practice problems
250ml plastic beakers, 2.0g samples of NH₄NO₃ and NaOH, distilled water, thermometers, measuring cylinders, analytical balance, calculators

KLB Secondary Chemistry Form 4, Pages 35-36
KLB Secondary Chemistry Form 4, Pages 36-38

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Thermochemical Equations

By the end of the lesson, the learner should be able to:
- Write thermochemical equations including enthalpy changes
-Define molar heat of solution
-Draw energy level diagrams for dissolution reactions
-Interpret thermochemical equations correctly

Using data from previous experiment, write thermochemical equations for NH₄NO₃ and NaOH dissolution. Show proper notation with state symbols and ΔH values. Draw corresponding energy level diagrams. Practice writing thermochemical equations for various reactions. Explain significance of molar quantities in equations.

Results from previous experiment, graph paper for energy level diagrams, practice examples

KLB Secondary Chemistry Form 4, Pages 38-39

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Solution of Concentrated Sulphuric Acid

By the end of the lesson, the learner should be able to:
- Determine heat of solution of concentrated sulphuric(VI) acid
-Apply safety precautions when handling concentrated acids
-Calculate enthalpy change considering density and purity
-Write thermochemical equation for the reaction

Teacher demonstration: Carefully add 2cm³ concentrated H₂SO₄ to 98cm³ distilled water in wrapped beaker (NEVER vice versa). Record temperature change. Calculate mass of acid using density (1.84 g/cm³) and purity (98%). Calculate molar heat of solution. Emphasize safety - always add acid to water.

Concentrated H₂SO₄, distilled water, 250ml plastic beaker, tissue paper, measuring cylinders, thermometer, safety equipment

KLB Secondary Chemistry Form 4, Pages 39-41

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Combustion

By the end of the lesson, the learner should be able to:
- Define molar heat of combustion
-Determine enthalpy of combustion of ethanol experimentally
-Explain why experimental values differ from theoretical values
-Calculate molar enthalpy of combustion from experimental data

Class experiment: Burn ethanol in small bottle with wick to heat 100cm³ water in glass beaker. Record initial and final masses of bottle+ethanol and temperature change. Calculate moles of ethanol burned and heat evolved. Determine molar enthalpy of combustion. Compare with theoretical value (-1368 kJ/mol). Discuss sources of error.

Ethanol, small bottles with wicks, 250ml glass beakers, tripod stands, wire gauze, thermometers, analytical balance, measuring cylinders

KLB Secondary Chemistry Form 4, Pages 41-44

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Displacement

By the end of the lesson, the learner should be able to:
- Define molar heat of displacement
-Investigate displacement of copper(II) ions by zinc
-Calculate molar heat of displacement
-Explain relationship between position in reactivity series and heat of displacement

Class experiment: Add 4.0g zinc powder to 100cm³ of 0.5M CuSO₄ solution in wrapped plastic beaker. Record temperature change and observations. Calculate moles of Zn used and Cu²⁺ displaced. Determine molar heat of displacement. Write ionic equation. Discuss why excess zinc is used. Compare with theoretical value.

Zinc powder, 0.5M CuSO₄ solution, 250ml plastic beakers, tissue paper, thermometers, analytical balance, stirring rods

KLB Secondary Chemistry Form 4, Pages 44-47

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Neutralization

By the end of the lesson, the learner should be able to:
- Define molar heat of neutralization
-Determine heat of neutralization of HCl with NaOH
-Compare neutralization enthalpies of strong and weak acids/bases
-Write ionic equations for neutralization reactions

Class experiment: Mix 50cm³ of 2M HCl with 50cm³ of 2M NaOH in wrapped beaker. Record temperature changes. Calculate molar heat of neutralization. Repeat with weak acid (ethanoic) and weak base (ammonia). Compare values. Write ionic equations. Explain why strong acid + strong base gives ~57.2 kJ/mol.

2M HCl, 2M NaOH, 2M ethanoic acid, 2M ammonia solution, measuring cylinders, thermometers, 250ml plastic beakers, tissue paper

KLB Secondary Chemistry Form 4, Pages 47-49

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Standard Conditions and Standard Enthalpy Changes

By the end of the lesson, the learner should be able to:
- Identify standard conditions for measuring enthalpy changes
-Define standard enthalpy changes using ΔH° notation
-Explain importance of standard conditions
-Use subscripts to denote different types of enthalpy changes

Q/A: Review previous enthalpy measurements. Introduce standard conditions: 25°C (298K) and 1 atmosphere pressure (101.325 kPa). Explain ΔH° notation and subscripts (ΔH°c for combustion, ΔH°f for formation, etc.). Discuss why standard conditions are necessary for comparison. Practice using correct notation.

Student books, examples of standard enthalpy data, notation practice exercises

KLB Secondary Chemistry Form 4, Pages 49

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Hess's Law - Introduction and Theory

By the end of the lesson, the learner should be able to:
- State Hess's Law
-Explain the principle of energy conservation in chemical reactions
-Understand that enthalpy change is independent of reaction route
-Apply Hess's Law to simple examples

Introduce Hess's Law: "The energy change in converting reactants to products is the same regardless of the route by which the chemical change occurs." Use methane formation example to show two routes giving same overall energy change. Draw energy cycle diagrams. Explain law of conservation of energy application.

Energy cycle diagrams for methane formation, chalkboard illustrations, worked examples from textbook

KLB Secondary Chemistry Form 4, Pages 49-52

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Energy Cycle Diagrams
Hess's Law Calculations

By the end of the lesson, the learner should be able to:
- Draw energy cycle diagrams
-Link enthalpy of formation with enthalpy of combustion
-Calculate unknown enthalpy changes using energy cycles
-Apply Hess's Law to determine enthalpy of formation
- Solve complex problems using Hess's Law
-Apply energy cycles to multi-step reactions
-Calculate enthalpy of formation from combustion data
-Use thermochemical equations in Hess's Law problems

Work through energy cycle for formation of CO from carbon and oxygen using combustion data. Draw cycle showing Route 1 (direct combustion) and Route 2 (formation then combustion). Calculate ΔH°f(CO) = ΔH°c(C) - ΔH°c(CO). Practice with additional examples including ethanol formation.
Work through detailed calculation for ethanol formation: 2C(s) + 3H₂(g) + ½O₂(g) → C₂H₅OH(l). Use combustion enthalpies of carbon (-393 kJ/mol), hydrogen (-286 kJ/mol), and ethanol (-1368 kJ/mol). Calculate ΔH°f(ethanol) = -278 kJ/mol. Practice with propane and other compounds.

Graph paper, energy cycle templates, combustion data tables, calculators
Worked examples, combustion data, calculators, step-by-step calculation sheets

KLB Secondary Chemistry Form 4, Pages 52-54
KLB Secondary Chemistry Form 4, Pages 54-56

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Lattice Energy and Hydration Energy

By the end of the lesson, the learner should be able to:
- Define lattice energy and hydration energy
-Explain relationship between heat of solution, lattice energy and hydration energy
-Draw energy cycles for dissolution of ionic compounds
-Calculate heat of solution using Born-Haber type cycles

Explain dissolution of NaCl: first lattice breaks (endothermic), then ions hydrate (exothermic). Define lattice energy as energy to form ionic solid from gaseous ions. Define hydration energy as energy when gaseous ions become hydrated. Draw energy cycle: ΔH(solution) = ΔH(lattice) + ΔH(hydration). Calculate for NaCl.

Energy cycle diagrams, lattice energy and hydration energy data tables, calculators

KLB Secondary Chemistry Form 4, Pages 54-56

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Factors Affecting Lattice and Hydration Energies

By the end of the lesson, the learner should be able to:
- Explain factors affecting lattice energy
-Explain factors affecting hydration energy
-Use data tables to identify trends
-Calculate enthalpies of solution for various ionic compounds

Analyze data tables showing lattice energies (Table 2.7) and hydration energies (Table 2.6). Identify trends: smaller ions and higher charges give larger lattice energies and hydration energies. Calculate heat of solution for MgCl₂ using: ΔH(solution) = +2489 + (-1891 + 2×(-384)) = -170 kJ/mol. Practice with other compounds.

Data tables from textbook, calculators, trend analysis exercises

KLB Secondary Chemistry Form 4, Pages 54-56

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Definition and Types of Fuels

By the end of the lesson, the learner should be able to:
- Define a fuel
-Classify fuels as solid, liquid, or gaseous
-State examples of each type of fuel
-Explain energy conversion in fuel combustion

Q/A: List fuels used at home and school. Define fuel as "substance that produces useful energy when it undergoes chemical or nuclear reaction." Classify examples: solids (coal, charcoal, wood), liquids (petrol, kerosene, diesel), gases (natural gas, biogas, LPG). Discuss energy conversions during combustion.

Examples of different fuels, classification charts, pictures of fuel types

KLB Secondary Chemistry Form 4, Pages 56

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Heating Values of Fuels

By the end of the lesson, the learner should be able to:
- Define heating value of a fuel
-Calculate heating values from molar enthalpies of combustion
-Compare heating values of different fuels
-Explain units of heating value (kJ/g)

Calculate heating value of ethanol: ΔH°c = -1360 kJ/mol, Molar mass = 46 g/mol, Heating value = 1360/46 = 30 kJ/g. Compare heating values from Table 2.8: methane (55 kJ/g), fuel oil (45 kJ/g), charcoal (33 kJ/g), wood (17 kJ/g). Discuss significance of these values for fuel selection.

Heating value data table, calculators, fuel comparison charts

KLB Secondary Chemistry Form 4, Pages 56-57

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Factors in Fuel Selection

By the end of the lesson, the learner should be able to:
- State factors that influence choice of fuel
-Explain why different fuels are chosen for different purposes
-Compare advantages and disadvantages of various fuels
-Apply selection criteria to real situations

Discuss seven factors: heating value, ease of combustion, availability, transportation, storage, environmental effects, cost. Compare wood/charcoal for domestic use vs methylhydrazine for rockets. Analyze why each is suitable for its purpose. Students suggest best fuels for cooking, heating, transport in their area.

Fuel comparison tables, local fuel availability data, cost analysis sheets

KLB Secondary Chemistry Form 4, Pages 57

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Environmental Effects of Fuels

By the end of the lesson, the learner should be able to:
- Identify environmental effects of burning fuels
-Explain formation and effects of acid rain
-Describe contribution to global warming
-State measures to reduce pollution from fuels

Discuss pollutants from fossil fuels: SO₂, SO₃, CO, NO₂ causing acid rain. Effects: damage to buildings, corrosion, acidification of lakes, soil leaching. CO₂ and hydrocarbons cause global warming leading to ice melting, climate change. Pollution reduction measures: catalytic converters, unleaded petrol, zero emission vehicles, alternative fuels.

Pictures of environmental damage, pollution data, examples of clean technology

KLB Secondary Chemistry Form 4, Pages 57-58

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Fuel Safety and Precautions

By the end of the lesson, the learner should be able to:
- State precautions necessary when using fuels
-Explain safety measures for different fuel types
-Identify hazards associated with improper fuel handling
-Apply safety principles to local situations

Discuss safety precautions: ventilation for charcoal stoves (CO poisoning), not running engines in closed garages, proper gas cylinder storage, fuel storage away from populated areas, keeping away from fuel spills. Relate to local situations and accidents. Students identify potential hazards in their environment.

Safety guideline charts, examples of fuel accidents, local safety case studies

KLB Secondary Chemistry Form 4, Pages 57-58

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Endothermic and Exothermic Reactions
Bond Breaking, Formation and Phase Changes

By the end of the lesson, the learner should be able to:
- Define endothermic and exothermic reactions using the ΔH notation
-Investigate what happens when ammonium nitrate and sodium hydroxide are separately dissolved in water
-Define enthalpy and enthalpy change
-Calculate enthalpy changes using ΔH = H(products) - H(reactants)
- Explain that energy changes are due to bond breaking and bond formation
-Investigate energy changes when solids and liquids are heated
-Define latent heat of fusion and vaporization
-Calculate energy changes using bond energies

Class experiment: Dissolve NH₄NO₃ and NaOH separately in water, record temperature changes in Table 2.1. Explain heat absorption vs evolution. Introduce enthalpy (H) and enthalpy change (ΔH). Calculate enthalpy changes from experimental data. Draw energy level diagrams showing relative energies.
Class experiment: Heat ice to melting then boiling, record temperature every minute. Plot heating curve. Explain constant temperature periods. Define latent heat of fusion/vaporization. Calculate energy changes in H₂ + Cl₂ → 2HCl using bond energies. Apply formula: ΔH = Energy absorbed - Energy released.

250ml plastic beakers, tissue paper, NH₄NO₃, NaOH pellets, distilled water, thermometers, calculators
Ice, glass beakers, thermometers, heating source, graph paper, bond energy data tables

KLB Secondary Chemistry Form 4, Pages 29-32
KLB Secondary Chemistry Form 4, Pages 32-36

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Determination of Enthalpy of Solution

By the end of the lesson, the learner should be able to:
- Carry out experiments to determine enthalpy changes of solution
-Calculate enthalpy change using ΔH = mcΔT
-Write correct thermochemical equations
-Define molar heat of solution

Class experiment: Dissolve exactly 2.0g NH₄NO₃ and 2.0g NaOH separately in 100ml water. Record temperature changes. Calculate enthalpy changes using ΔH = mcΔT. Calculate moles and molar heat of solution. Write thermochemical equations: NH₄NO₃(s) + aq → NH₄NO₃(aq) ΔH = +25.2 kJ mol⁻¹.

2.0g samples of NH₄NO₃ and NaOH, plastic beakers, thermometers, analytical balance, calculators

KLB Secondary Chemistry Form 4, Pages 36-39

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Solution of H₂SO₄ and Safety

By the end of the lesson, the learner should be able to:
- Determine heat of solution of concentrated sulphuric(VI) acid
-Apply safety precautions when handling concentrated acids
-Calculate enthalpy considering density and percentage purity
-Explain why experimental values differ from theoretical values

Teacher demonstration: Add 2cm³ concentrated H₂SO₄ to 98cm³ water (NEVER vice versa). Record temperature change. Calculate mass using density (1.84 g/cm³) and purity (98%). Calculate molar heat of solution. Emphasize safety: always add acid to water. Discuss sources of experimental error.

Concentrated H₂SO₄, distilled water, plastic beaker, tissue paper, thermometer, safety equipment

KLB Secondary Chemistry Form 4, Pages 39-41

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Combustion

By the end of the lesson, the learner should be able to:
- Carry out experiments to determine enthalpy of combustion of ethanol
-Define molar heat of combustion
-Calculate molar enthalpy of combustion from experimental data
-Explain why actual heats are lower than theoretical values

Class experiment: Burn ethanol to heat 100cm³ water. Record mass of ethanol burned and temperature change. Calculate moles of ethanol and heat evolved using ΔH = mcΔT. Determine molar enthalpy of combustion. Compare with theoretical (-1368 kJ/mol). Discuss heat losses to surroundings.

Ethanol, bottles with wicks, glass beakers, tripod stands, thermometers, analytical balance

KLB Secondary Chemistry Form 4, Pages 41-44

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Displacement

By the end of the lesson, the learner should be able to:
- Investigate enthalpy change when zinc reacts with copper(II) sulphate
-Define molar heat of displacement
-Calculate molar heat of displacement from experimental data
-Explain relationship between reactivity series and heat evolved

Class experiment: Add 4.0g zinc powder to 100cm³ of 0.5M CuSO₄. Record temperature change and observations (blue color fades, brown solid). Calculate moles and molar heat of displacement. Write ionic equation: Zn(s) + Cu²⁺(aq) → Zn²⁺(aq) + Cu(s). Explain why excess zinc is used.

Zinc powder, 0.5M CuSO₄ solution, plastic beakers, thermometers, analytical balance

KLB Secondary Chemistry Form 4, Pages 44-47

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Enthalpy of Neutralization

By the end of the lesson, the learner should be able to:
- Determine heat of neutralization of HCl with NaOH
-Define molar heat of neutralization
-Compare strong acid/base with weak acid/base combinations
-Write ionic equations including enthalpy changes

Class experiment: Mix 50cm³ of 2M HCl with 50cm³ of 2M NaOH. Record temperatures and calculate molar heat of neutralization. Repeat with weak acid/base. Compare values: strong + strong ≈ 57.2 kJ/mol, weak combinations give lower values. Write H⁺(aq) + OH⁻(aq) → H₂O(l) ΔH = -57.2 kJ mol⁻¹.

2M HCl, 2M NaOH, 2M ethanoic acid, 2M ammonia solution, measuring cylinders, thermometers, plastic beakers

KLB Secondary Chemistry Form 4, Pages 47-49

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Standard Conditions and Standard Enthalpy Changes
Hess's Law - Theory and Energy Cycles

By the end of the lesson, the learner should be able to:
- Define standard conditions for measuring enthalpy changes
-Use standard enthalpy notation ΔH°
-Apply correct notation for different types of enthalpy changes
-Explain importance of standardization for comparison

Q/A: Review enthalpy measurements. Define standard conditions: 25°C (298K) and 1 atmosphere (101.325 kPa). Introduce ΔH° notation where θ denotes standard. Show subscripts: ΔH°c (combustion), ΔH°f (formation), ΔH°neut (neutralization), ΔH°sol (solution). Practice using correct notation in thermochemical equations.

Student books, standard enthalpy data examples, notation practice exercises
Energy cycle diagrams for methane and CO formation, combustion data, calculators

KLB Secondary Chemistry Form 4, Pages 49

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Hess's Law Calculations

By the end of the lesson, the learner should be able to:
- Carry out calculations using Hess's Law
-Draw energy level diagrams
-Calculate enthalpy of formation from combustion data
-Solve worked examples using energy cycles

Work through ethanol formation: 2C(s) + 3H₂(g) + ½O₂(g) → C₂H₅OH(l). Draw energy cycle and level diagrams. Apply: ΔH°f(ethanol) = 2×ΔH°c(C) + 3×ΔH°c(H₂) - ΔH°c(ethanol) = 2×(-393) + 3×(-286) - (-1368) = -278 kJ/mol. Practice additional calculations from revision exercises.

Worked examples, combustion data tables, graph paper for diagrams, calculators

KLB Secondary Chemistry Form 4, Pages 52-56

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Lattice Energy and Hydration Energy
Definition and Types of Fuels

By the end of the lesson, the learner should be able to:
- Explain relationship between heat of solution, hydration and lattice energy
-Define lattice energy and hydration energy
-Draw energy cycles for dissolving ionic compounds
-Calculate heat of solution using energy cycles
- Define a fuel
-Classify fuels into solid, liquid and gaseous types
-Define heating value of a fuel
-Calculate heating values from molar enthalpies of combustion

Explain NaCl dissolution: lattice breaks (endothermic) then ions hydrate (exothermic). Define lattice energy as energy when ionic compound forms from gaseous ions. Define hydration energy as energy when gaseous ions become hydrated. Draw energy cycle: ΔH(solution) = ΔH(lattice) + ΔH(hydration). Calculate for NaCl: +781 + (-774) = +7 kJ/mol.
Define fuel as "substance producing useful energy in chemical/nuclear reaction." Classify: solids (coal, charcoal, wood), liquids (petrol, kerosene, diesel), gases (natural gas, biogas, LPG). Define heating value as "heat energy per unit mass." Calculate for ethanol: -1360 kJ/mol ÷ 46 g/mol = 30 kJ/g. Compare values from Table 2.8.

Energy cycle diagrams, hydration diagram (Fig 2.17), Tables 2.6 and 2.7 with lattice/hydration energies
Examples of local fuels, Table 2.8 showing heating values, calculators

KLB Secondary Chemistry Form 4, Pages 54-56
KLB Secondary Chemistry Form 4, Pages 56-57

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Fuel Selection Factors

By the end of the lesson, the learner should be able to:
- State and explain factors that influence choice of a fuel
-Compare suitability of fuels for different purposes
-Explain fuel selection for domestic use vs specialized applications
-Apply selection criteria to local situations

Discuss seven factors: heating value, ease of combustion, availability, transportation, storage, environmental effects, cost. Compare wood/charcoal for domestic use (cheap, available, safe, slow burning) vs methylhydrazine for rockets (rapid burning, high heat 4740 kJ/mol, easy ignition). Students analyze best fuels for their local area.

Fuel comparison tables, local fuel cost data, examples of specialized fuel applications

KLB Secondary Chemistry Form 4, Pages 57

ENERGY CHANGES IN PHYSICAL AND CHEMICAL PROCESSES

Environmental Effects and Safety

By the end of the lesson, the learner should be able to:
- Explain environmental effects of fuels
-Describe formation and effects of acid rain
-Identify measures to reduce pollution
-State safety precautions for fuel handling

Discuss pollutants: SO₂, NO₂ forming acid rain affecting buildings, lakes, vegetation. CO₂ causing global warming and climate change. Pollution reduction: catalytic converters, unleaded petrol, zero emission vehicles, alternative fuels. Safety: ventilation for charcoal, proper gas storage, fuel storage location, avoiding spills.

Pictures of environmental damage, pollution reduction examples, safety guideline charts

KLB Secondary Chemistry Form 4, Pages 57-58

REACTION RATES AND REVERSIBLE REACTIONS

Definition of Reaction Rate and Collision Theory

By the end of the lesson, the learner should be able to:
- Define rate of reaction and explain the term activation energy
-Describe collision theory and explain why not all collisions result in products
-Draw energy diagrams showing activation energy
-Explain how activation energy affects reaction rates

Q/A: Compare speeds of different reactions (precipitation vs rusting). Define reaction rate as "measure of how much reactants are consumed or products formed per unit time." Introduce collision theory: particles must collide with minimum energy (activation energy) for successful reaction. Draw energy diagram showing activation energy barrier. Discuss factors affecting collision frequency and energy.

Examples of fast/slow reactions, energy diagram templates, chalk/markers for diagrams

KLB Secondary Chemistry Form 4, Pages 64-65

REACTION RATES AND REVERSIBLE REACTIONS

Effect of Concentration on Reaction Rate

By the end of the lesson, the learner should be able to:
- Explain the effect of concentration on reaction rates
-Investigate reaction of magnesium with different concentrations of sulphuric acid
-Illustrate reaction rates graphically and interpret experimental data
-Calculate concentrations and plot graphs of concentration vs time

Class experiment: Label 4 conical flasks A-D. Add 40cm³ of 2M H₂SO₄ to A, dilute others with water (30+10, 20+20, 10+30 cm³). Drop 2cm magnesium ribbon into each, time complete dissolution. Record in Table 3.1. Calculate concentrations, plot graph. Explain: higher concentration → more collisions → faster reaction.

4 conical flasks, 2M H₂SO₄, distilled water, magnesium ribbon, stopwatch, measuring cylinders, graph paper

KLB Secondary Chemistry Form 4, Pages 65-67

REACTION RATES AND REVERSIBLE REACTIONS

Change of Reaction Rate with Time

By the end of the lesson, the learner should be able to:
- Describe methods used to measure rate of reaction
-Investigate how reaction rate changes as reaction proceeds
-Plot graphs of volume of gas vs time
-Calculate average rates at different time intervals

Class experiment: React 2cm magnesium ribbon with 100cm³ of 0.5M HCl in conical flask. Collect H₂ gas in graduated syringe as in Fig 3.4. Record gas volume every 30 seconds for 5 minutes in Table 3.2. Plot volume vs time graph. Calculate average rates between time intervals. Explain why rate decreases as reactants are consumed.

0.5M HCl, magnesium ribbon, conical flask, gas collection apparatus, graduated syringe, stopwatch, graph paper

KLB Secondary Chemistry Form 4, Pages 67-70

REACTION RATES AND REVERSIBLE REACTIONS

Effect of Temperature on Reaction Rate

By the end of the lesson, the learner should be able to:
- Explain the effect of temperature on reaction rates
-Investigate temperature effects using sodium thiosulphate and HCl
-Plot graphs of time vs temperature and 1/time vs temperature
-Apply collision theory to explain temperature effects

Class experiment: Place 30cm³ of 0.15M Na₂S₂O₃ in flasks at room temp, 30°C, 40°C, 50°C, 60°C. Mark cross on paper under flask. Add 5cm³ of 2M HCl, time until cross disappears. Record in Table 3.4. Plot time vs temperature and 1/time vs temperature graphs. Explain: higher temperature → more kinetic energy → more effective collisions.

0.15M Na₂S₂O₃, 2M HCl, conical flasks, water baths at different temperatures, paper with cross marked, stopwatch, thermometers

KLB Secondary Chemistry Form 4, Pages 70-73

REACTION RATES AND REVERSIBLE REACTIONS

Effect of Surface Area on Reaction Rate

By the end of the lesson, the learner should be able to:
- Explain the effect of surface area on reaction rates
-Investigate reaction of marble chips vs marble powder with HCl
-Compare reaction rates using gas collection
-Relate particle size to surface area and collision frequency

Class experiment: React 2.5g marble chips with 50cm³ of 1M HCl, collect CO₂ gas using apparatus in Fig 3.10. Record gas volume every 30 seconds. Repeat with 2.5g marble powder. Record in Table 3.5. Plot both curves on same graph. Write equation: CaCO₃ + 2HCl → CaCl₂ + H₂O + CO₂. Explain: smaller particles → larger surface area → more collision sites → faster reaction.

Marble chips, marble powder, 1M HCl, gas collection apparatus, balance, conical flasks, measuring cylinders, graph paper

KLB Secondary Chemistry Form 4, Pages 73-76

REACTION RATES AND REVERSIBLE REACTIONS

Effect of Catalysts on Reaction Rate
Effect of Light and Pressure on Reaction Rate

By the end of the lesson, the learner should be able to:
- Explain effects of suitable catalysts on reaction rates
-Investigate decomposition of hydrogen peroxide with and without catalyst
-Define catalyst and explain how catalysts work
-Compare activation energies in catalyzed vs uncatalyzed reactions
- Identify reactions affected by light
-Investigate effect of light on silver bromide decomposition
-Explain effect of pressure on gaseous reactions
-Give examples of photochemical reactions

Class experiment: Decompose 5cm³ of 20-volume H₂O₂ in 45cm³ water without catalyst, collect O₂ gas. Repeat adding 2g MnO₂ powder. Record gas volumes as in Fig 3.12. Compare rates and final mass of MnO₂. Write equation: 2H₂O₂ → 2H₂O + O₂. Define catalyst and explain how it lowers activation energy. Show energy diagrams for both pathways.
Teacher demonstration: Mix KBr and AgNO₃ solutions to form AgBr precipitate. Divide into 3 test tubes: place one in dark cupboard, one on bench, one in direct sunlight. Observe color changes after 10 minutes. Write equations. Discuss photochemical reactions: photography, Cl₂ + H₂, photosynthesis. Explain pressure effects on gaseous reactions through compression.

20-volume H₂O₂, MnO₂ powder, gas collection apparatus, balance, conical flasks, filter paper, measuring cylinders
0.1M KBr, 0.05M AgNO₃, test tubes, dark cupboard, direct light source, examples of photochemical reactions

KLB Secondary Chemistry Form 4, Pages 76-78
KLB Secondary Chemistry Form 4, Pages 78-80

REACTION RATES AND REVERSIBLE REACTIONS

Reversible Reactions

By the end of the lesson, the learner should be able to:
- State examples of simple reversible reactions
-Investigate heating of hydrated copper(II) sulphate
-Write equations for reversible reactions using double arrows
-Distinguish between reversible and irreversible reactions

Class experiment: Heat CuSO₄·5H₂O crystals in boiling tube A, collect liquid in tube B as in Fig 3.15. Observe color changes: blue → white + colorless liquid. Pour liquid back into tube A, observe return to blue. Write equation with double arrows: CuSO₄·5H₂O ⇌ CuSO₄ + 5H₂O. Give other examples: NH₄Cl ⇌ NH₃ + HCl. Compare with irreversible reactions.

CuSO₄·5H₂O crystals, boiling tubes, delivery tube, heating source, test tube holder

KLB Secondary Chemistry Form 4, Pages 78-80

REACTION RATES AND REVERSIBLE REACTIONS

Chemical Equilibrium

By the end of the lesson, the learner should be able to:
- Explain chemical equilibrium
-Define dynamic equilibrium
-Investigate acid-base equilibrium using indicators
-Explain why equilibrium appears static but is actually dynamic

Experiment: Add 0.5M NaOH to 2cm³ in boiling tube with universal indicator. Add 0.5M HCl dropwise until green color (neutralization point). Continue adding base then acid alternately, observe color changes. Explain equilibrium as state where forward and backward reaction rates are equal. Use NH₄Cl ⇌ NH₃ + HCl example to show dynamic nature. Introduce equilibrium symbol ⇌.

0.5M NaOH, 0.5M HCl, universal indicator, boiling tubes, droppers, examples of equilibrium systems

KLB Secondary Chemistry Form 4, Pages 80-82

REACTION RATES AND REVERSIBLE REACTIONS

Le Chatelier's Principle and Effect of Concentration

By the end of the lesson, the learner should be able to:
- State Le Chatelier's Principle
-Explain effect of concentration changes on equilibrium position
-Investigate bromine water equilibrium with acid/base addition
-Apply Le Chatelier's Principle to predict equilibrium shifts

Experiment: Add 2M NaOH dropwise to 20cm³ bromine water until colorless. Then add 2M HCl until excess, observe color return. Write equation: Br₂ + H₂O ⇌ HBr + HBrO. Explain Le Chatelier's Principle: "When change applied to system at equilibrium, system moves to oppose that change." Demonstrate with chromate/dichromate equilibrium: CrO₄²⁻ + H⁺ ⇌ Cr₂O₇²⁻ + H₂O.

Bromine water, 2M NaOH, 2M HCl, beakers, chromate/dichromate solutions for demonstration

KLB Secondary Chemistry Form 4, Pages 82-84

REACTION RATES AND REVERSIBLE REACTIONS

Effect of Pressure and Temperature on Equilibrium

By the end of the lesson, the learner should be able to:
- Explain effect of pressure changes on equilibrium
-Explain effect of temperature changes on equilibrium
-Investigate NO₂/N₂O₄ equilibrium with temperature
-Apply Le Chatelier's Principle to industrial processes

Teacher demonstration: React copper turnings with concentrated HNO₃ to produce NO₂ gas in test tube. Heat and cool the tube, observe color changes: brown ⇌ pale yellow representing 2NO₂ ⇌ N₂O₄. Explain pressure effects using molecule count. Show Table 3.7 with pressure effects. Discuss temperature effects: heating favors endothermic direction, cooling favors exothermic direction. Use Table 3.8.

Copper turnings, concentrated HNO₃, test tubes, heating source, ice bath, gas collection apparatus, safety equipment

KLB Secondary Chemistry Form 4, Pages 84-87

REACTION RATES AND REVERSIBLE REACTIONS

Industrial Applications - Haber Process

By the end of the lesson, the learner should be able to:
- Apply equilibrium principles to Haber Process
-Explain optimum conditions for ammonia manufacture
-Calculate effect of temperature and pressure on yield
-Explain role of catalysts in industrial processes

Analyze Haber Process: N₂ + 3H₂ ⇌ 2NH₃ ΔH = -92 kJ/mol. Apply Le Chatelier's Principle: high pressure favors forward reaction (4 molecules → 2 molecules), low temperature favors exothermic forward reaction but slows rate. Explain optimum conditions: 450°C temperature, 200 atmospheres pressure, iron catalyst. Discuss removal of NH₃ to shift equilibrium right. Economic considerations.

Haber Process flow diagram, equilibrium data showing temperature/pressure effects on NH₃ yield, industrial catalyst information

KLB Secondary Chemistry Form 4, Pages 87-89

REACTION RATES AND REVERSIBLE REACTIONS

Industrial Applications - Contact Process

By the end of the lesson, the learner should be able to:
- Apply equilibrium principles to Contact Process
-Explain optimum conditions for sulphuric acid manufacture
-Compare different industrial equilibrium processes
-Evaluate economic factors in industrial chemistry

Analyze Contact Process: 2SO₂ + O₂ ⇌ 2SO₃ ΔH = -197 kJ/mol. Apply principles: high pressure favors forward reaction (3 molecules → 2 molecules), low temperature favors exothermic reaction. Explain optimum conditions: 450°C, atmospheric pressure, V₂O₅ catalyst, 96% conversion. Compare with Haber Process. Discuss catalyst choice and economic factors.

Contact Process flow diagram, comparison table with Haber Process, catalyst effectiveness data

KLB Secondary Chemistry Form 4, Pages 89

ELECTROCHEMISTRY

Redox Reactions and Oxidation Numbers
Oxidation Numbers in Naming and Redox Identification

By the end of the lesson, the learner should be able to:
Define redox reactions in terms of electron transfer
- State rules for assigning oxidation numbers
- Calculate oxidation numbers in compounds
- Identify oxidation and reduction processes

Q/A: Review previous knowledge
- Experiment 4.1: Iron filings + copper(II) sulphate
- Experiment 4.2: Iron(II) ions + hydrogen peroxide
- Discussion on oxidation number rules with examples

Iron filings, 1M CuSO₄, 1M FeSO₄, 2M NaOH, 20V H₂O₂, test tubes
Compound charts, calculators, student books, practice exercises

KLB Secondary Chemistry Form 4, Pages 108-116

ELECTROCHEMISTRY

Displacement Reactions - Metals and Halogens
Electrochemical Cells and Cell Diagrams
Standard Electrode Potentials
Calculating Cell EMF and Predicting Reactions

By the end of the lesson, the learner should be able to:
Explain displacement reactions using electron transfer
- Arrange metals and halogens by reactivity
- Predict displacement reactions
- Compare oxidizing powers of halogens
Define standard electrode potential
- Describe standard hydrogen electrode
- List standard conditions
- Use electrode potential tables effectively

Experiment 4.3: Metal displacement reactions - systematic testing
- Experiment 4.4: Halogen displacement (FUME CUPBOARD)
- Tabulate results and arrange by reactivity
Study standard hydrogen electrode setup
- Discussion of standard conditions (25°C, 1M, 1 atm)
- Introduction to electrode potential series
- Practice reading potential tables

Various metals (Ca, Mg, Zn, Fe, Pb, Cu), metal salt solutions, halogens (Cl₂, Br₂, I₂), halide solutions
Metal electrodes, 1M metal salt solutions, voltmeters, salt bridges, connecting wires
Standard electrode potential table, diagrams, charts showing standard conditions
Calculators, electrode potential data, worked examples, practice problems

KLB Secondary Chemistry Form 4, Pages 116-122
KLB Secondary Chemistry Form 4, Pages 129-133

ELECTROCHEMISTRY

Types of Electrochemical Cells
Electrolysis of Aqueous Solutions I
Electrolysis of Aqueous Solutions II

By the end of the lesson, the learner should be able to:
Describe functioning of primary and secondary cells
- Compare different cell types
- Explain fuel cell operation
- State applications of electrochemical cells

Study dry cell (Le Clanche) and lead-acid accumulator
- Hydrogen-oxygen fuel cell operation
- Compare cell types and applications
- Discussion on advantages/disadvantages

Cell diagrams, sample batteries, charts showing cell applications
Dilute and concentrated NaCl solutions, carbon electrodes, gas collection tubes, test equipment
U-tube apparatus, 2M H₂SO₄, 0.5M MgSO₄, platinum/carbon electrodes, gas syringes

KLB Secondary Chemistry Form 4, Pages 138-141

ELECTROCHEMISTRY

Effect of Electrode Material on Electrolysis

By the end of the lesson, the learner should be able to:
Compare inert vs reactive electrodes
- Investigate electrode dissolution
- Explain electrode selection importance
- Analyze copper purification process

Experiment 4.9: Electrolysis of CuSO₄ with carbon vs copper electrodes
- Weigh electrodes before/after
- Observe color changes
- Discussion on electrode effects

Copper and carbon electrodes, 3M CuSO₄ solution, accurate balance, beakers, connecting wires

KLB Secondary Chemistry Form 4, Pages 141-148

ELECTROCHEMISTRY

Factors Affecting Electrolysis

By the end of the lesson, the learner should be able to:
Identify factors affecting preferential discharge
- Explain electrochemical series influence
- Discuss concentration and electrode effects
- Predict electrolysis products

Review electrochemical series and discharge order
- Analysis of concentration effects on product formation
- Summary of all factors affecting electrolysis
- Practice prediction problems

Electrochemical series chart, summary tables, practice exercises, student books

KLB Secondary Chemistry Form 4, Pages 153-155

ELECTROCHEMISTRY

Applications of Electrolysis I

By the end of the lesson, the learner should be able to:
Describe electrolytic extraction of reactive metals
- Explain electroplating process
- Apply electrolysis principles to metal coating
- Design electroplating setup

Discussion: Extraction of Na, Mg, Al by electrolysis
- Practical: Electroplate iron nail with copper
- Calculate plating requirements
- Industrial applications

Iron nails, copper electrodes, CuSO₄ solution, power supply, industrial process diagrams

KLB Secondary Chemistry Form 4, Pages 155-157

ELECTROCHEMISTRY

Applications of Electrolysis II

By the end of the lesson, the learner should be able to:
Describe manufacture of NaOH and Cl₂ from brine
- Explain mercury cell operation
- Analyze industrial electrolysis processes
- Discuss environmental considerations

Study mercury cell for NaOH production
- Flow chart analysis of industrial processes
- Discussion on applications and environmental impact
- Purification of metals

Flow charts, mercury cell diagrams, environmental impact data, industrial case studies

KLB Secondary Chemistry Form 4, Pages 155-157

ELECTROCHEMISTRY

Faraday's Laws and Quantitative Electrolysis

By the end of the lesson, the learner should be able to:
State Faraday's laws of electrolysis
- Define Faraday constant
- Calculate mass deposited in electrolysis
- Relate electricity to amount of substance

Experiment 4.10: Quantitative electrolysis of CuSO₄
- Measure mass vs electricity passed
- Calculate Faraday constant
- Verify Faraday's laws

Accurate balance, copper electrodes, CuSO₄ solution, ammeter, timer, calculators

KLB Secondary Chemistry Form 4, Pages 161-164

ELECTROCHEMISTRY

Electrolysis Calculations I

By the end of the lesson, the learner should be able to:
Calculate mass of products from electrolysis
- Determine volumes of gases evolved
- Apply Faraday's laws to numerical problems
- Solve basic electrolysis calculations

Worked examples: Mass and volume calculations
- Problems involving different ions
- Practice with Faraday constant
- Basic numerical problems

Calculators, worked examples, practice problems, gas volume data, Faraday constant

KLB Secondary Chemistry Form 4, Pages 161-164

ELECTROCHEMISTRY

Electrolysis Calculations II
Advanced Applications and Problem Solving

By the end of the lesson, the learner should be able to:
Determine charge on ions from electrolysis data
- Calculate current-time relationships
- Solve complex multi-step problems
- Apply concepts to industrial situations
Solve examination-type electrochemistry problems
- Apply all concepts in integrated problems
- Analyze real-world electrochemical processes
- Practice complex calculations

Complex problems: Determine ionic charges
- Current-time-mass relationships
- Multi-step calculations
- Industrial calculation examples
Comprehensive problems combining redox, cells, and electrolysis
- Past examination questions
- Industrial case study analysis
- Advanced problem-solving techniques

Calculators, complex problem sets, industrial data, student books
Past papers, comprehensive problem sets, industrial case studies, calculators

KLB Secondary Chemistry Form 4, Pages 161-164
KLB Secondary Chemistry Form 4, Pages 108-164

METALS

Chief Ores of Metals and General Extraction Methods
Occurrence and Extraction of Sodium

By the end of the lesson, the learner should be able to:
Name chief ores of common metals
- State formulas of metal ores
- Explain general methods of ore concentration
- Describe factors affecting extraction methods

Q/A: Review metallic bonding and reactivity
- Study Table 5.1 - metal ores and formulas
- Discussion on ore concentration methods
- Froth flotation demonstration

Chart of metal ores, ore samples if available, Table 5.1, flotation apparatus demonstration
Down's cell diagram, charts showing sodium occurrence, electrode reaction equations

KLB Secondary Chemistry Form 4, Pages 139-140

METALS

Occurrence and Extraction of Aluminium I
Extraction of Aluminium II - Electrolysis

By the end of the lesson, the learner should be able to:
Describe occurrence and ores of aluminium
- Explain ore concentration process
- Write equations for bauxite purification
- Describe amphoteric nature of aluminium oxide

Study aluminium occurrence and bauxite composition
- Demonstration of amphoteric properties
- Equations for bauxite dissolution in NaOH
- Discussion on impurity removal

Bauxite samples, NaOH solution, charts showing aluminium extraction steps, chemical equations
Electrolytic cell diagram, cryolite samples, graphite electrodes, energy consumption data

KLB Secondary Chemistry Form 4, Pages 142-143

METALS

Occurrence and Extraction of Iron
Extraction of Zinc

By the end of the lesson, the learner should be able to:
Describe iron ores and occurrence
- Explain blast furnace operation
- Write equations for iron extraction reactions
- Describe slag formation process

Study iron ores and blast furnace structure
- Analysis of temperature zones in furnace
- Write reduction equations
- Discussion on limestone role and slag formation

Blast furnace diagram, iron ore samples, coke, limestone, temperature zone charts
Zinc ore samples, flow charts showing both methods, electrolytic cell diagrams

KLB Secondary Chemistry Form 4, Pages 143-145

METALS

Extraction of Lead and Copper
Physical Properties of Metals

By the end of the lesson, the learner should be able to:
Explain extraction of lead from galena
- Describe copper extraction from copper pyrites
- Write relevant chemical equations
- Compare purification methods

Study galena roasting and reduction
- Copper pyrites multi-step extraction
- Electrolytic purification processes
- Discussion on blister copper formation

Lead and copper ore samples, extraction flow charts, electrolytic purification diagrams
Table 5.2, metal samples, conductivity apparatus, density measurement equipment

KLB Secondary Chemistry Form 4, Pages 148-151

METALS

Chemical Properties I - Reaction with Air

By the end of the lesson, the learner should be able to:
Investigate metal reactions with air and oxygen
- Write balanced equations for metal oxidation
- Compare reactivity patterns
- Explain tarnishing and oxide formation

Experiment 5.1: Heat metals in air - sodium, aluminium, zinc, iron, copper
- Observe color changes and products
- Record observations in Table 5.3
- Write oxidation equations

Deflagrating spoons, metal samples (Na, Al, Zn, Fe, Cu), Bunsen burners, safety equipment

KLB Secondary Chemistry Form 4, Pages 152-154

METALS

Chemical Properties II - Reaction with Water

By the end of the lesson, the learner should be able to:
Test metal reactions with cold water and steam
- Arrange metals by reactivity
- Explain aluminium's apparent unreactivity
- Write chemical equations for reactions

Experiment 5.2: Test metals with cold water and steam
- Use Table 5.4 for observations
- Test solutions with indicators
- Arrange metals in reactivity order

Metal samples, cold water, steam generator, test tubes, universal indicator, safety equipment

KLB Secondary Chemistry Form 4, Pages 154-156

METALS

Chemical Properties III - Reaction with Chlorine

By the end of the lesson, the learner should be able to:
Investigate metal reactions with chlorine gas
- Write equations for chloride formation
- Compare reaction vigor
- Observe product characteristics

Experiment 5.3: React hot metals with chlorine gas (FUME CUPBOARD)
- Observe color changes and fume formation
- Record all observations
- Write balanced equations

Chlorine gas, gas jars, metal samples, tongs, deflagrating spoons, fume cupboard, safety equipment

KLB Secondary Chemistry Form 4, Pages 156-157

METALS

Chemical Properties IV - Reaction with Acids
Uses of Metals I - Sodium and Aluminium

By the end of the lesson, the learner should be able to:
Test metal reactions with dilute and concentrated acids
- Compare reaction patterns
- Write chemical equations
- Explain passivation effects
State uses of sodium and its compounds
- Explain aluminium applications
- Relate properties to uses
- Describe alloy formation and uses

Experiment 5.4: Test metals with various acids - HCl, HNO₃, H₂SO₄
- Use Table 5.5 for systematic recording
- Observe gas evolution
- Discuss passivation
Discussion on sodium uses in industry
- Aluminium applications in transport and construction
- Study duralumin and other alloys
- Property-use relationships

Various acids (dilute and concentrated), metal strips, test tubes, gas collection apparatus, safety equipment
Charts showing metal applications, alloy samples, aircraft parts, cooking vessels

KLB Secondary Chemistry Form 4, Pages 157-158
KLB Secondary Chemistry Form 4, Pages 158-159

METALS

Uses of Metals II - Zinc, Copper and Iron

By the end of the lesson, the learner should be able to:
Explain galvanization process
- Describe copper electrical applications
- Compare iron, steel, and cast iron uses
- Analyze alloy compositions and properties

Study galvanization and rust prevention
- Copper in electrical applications
- Different types of steel and their compositions
- Alloy property comparisons

Galvanized sheets, copper wires, steel samples, alloy composition charts, brass and bronze samples

KLB Secondary Chemistry Form 4, Pages 159-161

METALS

Steel Types and Alloys

By the end of the lesson, the learner should be able to:
Compare cast iron, wrought iron, and steel
- Analyze different steel compositions
- Explain alloy property enhancement
- Describe specialized steel applications

Study cast iron, wrought iron, mild steel, and stainless steel
- Analyze carbon content effects
- Specialized steels for tools and instruments
- Discussion on alloy design

Steel samples with different compositions, carbon content charts, specialized tools, stainless steel items

KLB Secondary Chemistry Form 4, Pages 159-161

METALS
ORGANIC CHEMISTRY II

Environmental Effects of Metal Extraction
Introduction to Alkanols and Nomenclature

By the end of the lesson, the learner should be able to:
Identify environmental impacts of mining
- Explain pollution from metal extraction
- Describe waste management strategies
- Discuss NEMA regulations in Kenya

Analysis of mining environmental impact
- Air, water, and land pollution from extraction
- Waste management and slag utilization
- NEMA role and regulations

Environmental impact case studies, pollution images, NEMA regulation documents, waste management examples
Molecular models, Table 6.1 and 6.2, alkanol structure charts, student books

KLB Secondary Chemistry Form 4, Pages 161-162

ORGANIC CHEMISTRY II

Isomerism in Alkanols
Laboratory Preparation of Ethanol
Industrial Preparation and Physical Properties

By the end of the lesson, the learner should be able to:
Explain positional and chain isomerism
- Draw isomers of given alkanols
- Name different isomeric forms
- Classify isomers as primary, secondary, or tertiary

Study positional isomerism examples (propan-1-ol vs propan-2-ol)
- Practice drawing chain isomers
- Exercises on isomer identification and naming
- Discussion on structural differences

Isomer structure charts, molecular models, practice worksheets, student books
Sugar, yeast, warm water, conical flask, delivery tube, lime water, thermometer
Table 6.3, industrial process diagrams, ethene structure models, property comparison charts

KLB Secondary Chemistry Form 4, Pages 170-171

ORGANIC CHEMISTRY II

Chemical Properties of Alkanols I
Chemical Properties of Alkanols II

By the end of the lesson, the learner should be able to:
Test reactions of ethanol with various reagents
- Write equations for ethanol reactions
- Identify products formed
- Explain reaction mechanisms

Experiment 6.2: Test ethanol with burning, universal indicator, sodium metal, acids
- Record observations in Table 6.4
- Write balanced equations
- Discuss reaction types

Ethanol, sodium metal, universal indicator, concentrated H₂SO₄, ethanoic acid, test tubes
Acidified potassium chromate/manganate, ethanoic acid, concentrated H₂SO₄, heating apparatus

KLB Secondary Chemistry Form 4, Pages 173-175

ORGANIC CHEMISTRY II

Uses of Alkanols and Health Effects
Introduction to Alkanoic Acids

By the end of the lesson, the learner should be able to:
State various uses of alkanols
- Explain health effects of alcohol consumption
- Discuss methylated spirits
- Analyze alcohol in society

Discussion on alkanol applications as solvents, fuels, antiseptics
- Health effects of alcohol consumption
- Methylated spirits composition
- Social implications

Charts showing alkanol uses, health impact data, methylated spirit samples, discussion materials
Alkanoic acid structure charts, Table 6.5 and 6.6, molecular models, student books

KLB Secondary Chemistry Form 4, Pages 176-177

ORGANIC CHEMISTRY II

Laboratory Preparation of Ethanoic Acid

By the end of the lesson, the learner should be able to:
Prepare ethanoic acid by oxidation
- Write equations for preparation
- Set up oxidation apparatus
- Identify product by testing

Experiment 6.3: Oxidize ethanol using acidified KMnO₄
- Set up heating and distillation apparatus
- Collect distillate at 118°C
- Test product properties

Ethanol, KMnO₄, concentrated H₂SO₄, distillation apparatus, thermometer, round-bottom flask

KLB Secondary Chemistry Form 4, Pages 179-180

ORGANIC CHEMISTRY II

Physical and Chemical Properties of Alkanoic Acids
Esterification and Uses of Alkanoic Acids

By the end of the lesson, the learner should be able to:
Investigate chemical reactions of ethanoic acid
- Test with various reagents
- Write chemical equations
- Analyze acid strength
Explain ester formation process
- Write esterification equations
- State uses of alkanoic acids
- Prepare simple esters

Experiment following Table 6.8: Test ethanoic acid with indicators, metals, carbonates, bases
- Record observations
- Write equations
- Discuss weak acid behavior
Complete esterification experiments
- Study concentrated H₂SO₄ as catalyst
- Write general esterification equation
- Discuss applications in food, drugs, synthetic fibres

2M ethanoic acid, universal indicator, Mg strip, Na₂CO₃, NaOH, phenolphthalein, test tubes
Ethanoic acid, ethanol, concentrated H₂SO₄, test tubes, heating apparatus, cold water

KLB Secondary Chemistry Form 4, Pages 180-182
KLB Secondary Chemistry Form 4, Pages 182-183

ORGANIC CHEMISTRY II

Introduction to Detergents and Soap Preparation

By the end of the lesson, the learner should be able to:
Define detergents and classify types
- Explain saponification process
- Prepare soap in laboratory
- Compare soapy and soapless detergents

Study soap vs soapless detergent differences
- Experiment 6.5: Saponify castor oil with NaOH
- Add salt for salting out
- Test soap formation

Castor oil, 4M NaOH, NaCl, evaporating dish, water bath, stirring rod, filter paper

KLB Secondary Chemistry Form 4, Pages 183-186

ORGANIC CHEMISTRY II

Mode of Action of Soap and Hard Water Effects

By the end of the lesson, the learner should be able to:
Explain soap molecule structure
- Describe cleaning mechanism
- Investigate hard water effects
- Compare soap performance in different waters

Study hydrophobic and hydrophilic ends
- Demonstrate micelle formation
- Test soap in distilled vs hard water
- Observe scum formation
- Write precipitation equations

Soap samples, distilled water, hard water (CaCl₂/MgSO₄ solutions), test tubes, demonstration materials

KLB Secondary Chemistry Form 4, Pages 186-188

ORGANIC CHEMISTRY II

Soapless Detergents and Environmental Effects

By the end of the lesson, the learner should be able to:
Explain soapless detergent preparation
- Compare advantages/disadvantages
- Discuss environmental impact
- Analyze pollution effects

Study alkylbenzene sulphonate preparation
- Compare Table 6.9 - soap vs soapless
- Discussion on eutrophication and biodegradability
- Environmental awareness

Flow charts of detergent manufacture, Table 6.9, environmental impact data, sample detergents

KLB Secondary Chemistry Form 4, Pages 188-191

ORGANIC CHEMISTRY II

Introduction to Polymers and Addition Polymerization

By the end of the lesson, the learner should be able to:
Define polymers, monomers, and polymerization
- Explain addition polymerization
- Draw polymer structures
- Calculate polymer properties

Study polymer concept and terminology
- Practice drawing addition polymers from monomers
- Examples: polyethene, polypropene, PVC
- Calculate molecular masses

Polymer samples, monomer structure charts, molecular models, calculators, polymer formation diagrams

KLB Secondary Chemistry Form 4, Pages 191-195

ORGANIC CHEMISTRY II

Addition Polymers - Types and Properties

By the end of the lesson, the learner should be able to:
Identify different addition polymers
- Draw structures from monomers
- Name common polymers
- Relate structure to properties

Study polystyrene, PTFE, perspex formation
- Practice identifying monomers from polymer structures
- Work through polymer calculation examples
- Properties analysis

Various polymer samples, structure identification exercises, calculation worksheets, Table 6.10

KLB Secondary Chemistry Form 4, Pages 195-197

ORGANIC CHEMISTRY II

Condensation Polymerization and Natural Polymers

By the end of the lesson, the learner should be able to:
Explain condensation polymerization
- Compare with addition polymerization
- Study natural polymers
- Analyze nylon formation

Study nylon 6,6 formation from diamine and dioic acid
- Natural polymers: starch, protein, rubber
- Vulcanization process
- Compare synthetic vs natural

Nylon samples, rubber samples, condensation reaction diagrams, natural polymer examples

KLB Secondary Chemistry Form 4, Pages 197-200

ORGANIC CHEMISTRY II

Polymer Properties and Applications

By the end of the lesson, the learner should be able to:
Compare advantages and disadvantages of synthetic polymers
- State uses of different polymers
- Discuss environmental concerns
- Analyze polymer selection

Study Table 6.10 - polymer uses
- Advantages: strength, lightness, moldability
- Disadvantages: non-biodegradability, toxic gases
- Application analysis

Table 6.10, polymer application samples, environmental impact studies, product examples

KLB Secondary Chemistry Form 4, Pages 200-201

ORGANIC CHEMISTRY II
RADIOACTIVITY

Comprehensive Problem Solving and Integration
Introduction, Nuclear Stability and Types of Radioactivity
Types of Radiation and Their Properties
Radioactive Decay and Half-Life Concept

By the end of the lesson, the learner should be able to:
Solve complex problems involving alkanols and acids
- Apply knowledge to practical situations
- Integrate polymer concepts
- Practice examination questions
Identify alpha, beta, and gamma radiations
- Compare penetrating abilities and ionizing power
- Explain electric field deflection
- Analyze safety implications

Worked examples on organic synthesis
- Problem-solving on isomers, reactions, polymers
- Integration of all unit concepts
- Practice examination-style questions
Study alpha (α), beta (β), gamma (γ) characteristics
- Figure 7.2 - penetrating power demonstration
- Figure 7.3 - electric field effects
- Discussion on radiation protection and detection

Comprehensive problem sets, past examination papers, calculators, organic chemistry summary charts
Periodic table, atomic structure charts, Table 7.1, nuclear stability diagrams
Radiation type charts, penetration diagrams, electric field illustrations, safety equipment charts
Graph paper, Table 7.2 data, calculators, decay curve examples, half-life data table

KLB Secondary Chemistry Form 4, Pages 167-201
KLB Secondary Chemistry Form 4, Pages 201-204

RADIOACTIVITY

Half-Life Calculations and Problem Solving
Nuclear Reactions and Equations

By the end of the lesson, the learner should be able to:
Solve complex half-life problems
- Determine original amounts from remaining masses
- Apply step-by-step and formula methods
- Compare isotope decay rates

Worked examples on half-life calculations using both methods
- Practice determining original amounts
- Study various isotope half-lives
- Comprehensive problem-solving sessions

Calculators, comprehensive problem sets, worked examples, isotope half-life comparison tables
Nuclear equation examples, periodic table, conservation law charts, practice worksheets

KLB Secondary Chemistry Form 4, Pages 204-206

RADIOACTIVITY

Radioactive Decay Series and Sequential Reactions
Nuclear Fission and Chain Reactions

By the end of the lesson, the learner should be able to:
Explain sequential radioactive decay
- Trace decay series pathways
- Identify stable end products
- Complete partial decay series

Study thorium-232 decay series example
- Trace sequential alpha and beta emissions
- Identify stable lead-208 endpoint
- Practice completing decay series with missing nuclides

Decay series charts, thorium series diagram, nuclide stability charts, practice decay series
Fission reaction diagrams, chain reaction illustrations, nuclear reactor diagrams, energy calculation examples

KLB Secondary Chemistry Form 4, Pages 206-207

RADIOACTIVITY

Nuclear Fusion and Energy Comparisons
Medical and Diagnostic Applications

By the end of the lesson, the learner should be able to:
Define nuclear fusion process
- Compare fusion with fission processes
- Write fusion equations
- Explain stellar energy production and fusion applications

Study hydrogen fusion examples
- Compare fusion vs fission characteristics and energy yields
- Stellar fusion processes
- Hydrogen bomb vs nuclear reactor principles

Fusion reaction diagrams, comparison tables, stellar fusion charts, energy comparison data
Medical radioisotope charts, treatment procedure diagrams, diagnostic equipment images, case studies

KLB Secondary Chemistry Form 4, Pages 207-208

RADIOACTIVITY

Industrial, Agricultural and Dating Applications

By the end of the lesson, the learner should be able to:
Explain industrial leak detection
- Describe agricultural monitoring techniques
- Discuss carbon-14 dating principles
- Analyze food preservation methods

Study leak detection using short half-life isotopes
- Carbon-14 dating of archaeological materials
- Phosphorus tracking in agriculture
- Gamma radiation food preservation

Carbon dating examples, agricultural application charts, industrial use diagrams, food preservation data

KLB Secondary Chemistry Form 4, Pages 208-209

RADIOACTIVITY

Radiation Hazards and Environmental Impact

By the end of the lesson, the learner should be able to:
Identify radiation health hazards
- Explain genetic mutation effects
- Discuss major nuclear accidents
- Analyze long-term environmental contamination

Study Chernobyl and Three Mile Island accidents
- Genetic mutation and cancer effects
- Long-term radiation exposure consequences
- Nuclear waste disposal challenges

Accident case studies, environmental impact data, radiation exposure charts, contamination maps

KLB Secondary Chemistry Form 4, Pages 209-210

RADIOACTIVITY

Safety Measures and International Control

By the end of the lesson, the learner should be able to:
Explain radiation protection principles
- Describe proper storage and disposal methods
- Discuss IAEA role and standards
- Analyze monitoring and control systems

Study IAEA guidelines and international cooperation
- Radiation protection protocols and ALARA principle
- Safe storage, transport and disposal methods
- Environmental monitoring systems

IAEA guidelines, safety protocol charts, monitoring equipment diagrams, international cooperation data

KLB Secondary Chemistry Form 4, Pages 209-210

RADIOACTIVITY

Half-Life Problem Solving and Graph Analysis

By the end of the lesson, the learner should be able to:
Solve comprehensive half-life problems
- Analyze experimental decay data
- Plot and interpret decay curves
- Determine half-lives graphically

Plot decay curves from experimental data
- Determine half-lives from graphs
- Analyze count rate vs time data
- Complex half-life calculation problems

Graph paper, experimental data sets, calculators, statistical analysis examples, comprehensive problem sets

KLB Secondary Chemistry Form 4, Pages 199-210

RADIOACTIVITY

Nuclear Equations and Conservation Laws

By the end of the lesson, the learner should be able to:
Balance complex nuclear equations
- Complete nuclear reaction series
- Identify unknown nuclides using conservation laws
- Apply mass-energy relationships

Practice balancing nuclear reactions with multiple steps
- Complete partial decay series
- Identify missing nuclides using conservation principles
- Mass-energy calculation problems

Nuclear equation worksheets, periodic table, decay series diagrams, conservation law examples

KLB Secondary Chemistry Form 4, Pages 199-210